To place orders for any of the products, please click here.

GAS VALVE INSTALL KIT
Gas Valve Install Kit for use with 63mm and 32mm Gas Valves. This product has been developed over the past five years, to satisfy the high demands of Transco, not only in the technical aspect but also in its ease of installation.
 
Gas Install Kit Component Parts

Surface box
Chamber Height adjustment Collar
Guard Pipe
Protective saddle with positive strap fixing

This Gas Valve Install Kit comes packed in a poly- sleeve with full fitting instructions.

LARGE GAS VALVE INSTALL KIT FOR USE WITH LARGER DONKIN TYPE VALVE
Developed alongside the 63mm/32mm Valve Install Kit but for use where a large Donkin 555, 80mm and 100mm type valve is installed in the footpath.
 
Large Gas Install Kit Component Parts

Surface box
Chamber Height adjustment Collar
Guard Pipe with cutouts
Small “Do-nut” base adaptor

This Gas Valve Install Kit comes packed in a poly- sleeve with full fitting instructions.

NT1/GIK - LARGE GAS VALVE INSTALL KIT
Again for use with Donkin 555 type valve, 80mm and 100mm. For use within both the footpath and carriageway.
 
NT1/GIK Gas Install Kit Component Parts
Ironwork location adaptors, Sleeve adaptor or retaining clips
Jig-Brix™ Chamber
225mm x 225mm Internal Dimensions x depth, to suit, in 39mm increments
Camber adjustment available in 20mm and 5mm increments
Large “Do-nut” Base adaptor

NT5/GIK - LARGE GAS VALVE INSTALL KIT
For use with large Donkin type valve, 100mm - 300mm. Can be fitted within the carriageway.
 
NT5/GIK Gas Install Kit Component Parts
Ironwork location adaptors, retaining clips
Jig-Brix™ Chamber
300mm x 300mm Internal Dimensions x depth, to suit, in 39mm increments
Camber adjustment available in 20mm and 5mm increments
Large “Do-nut” Base adaptor

QUAD BOX SURFACE BOX
The Quad box surface box can be badged Water, Gas CATV etc, this product has evolved over the past seventeen years and is now used throughout the UK by most of the utilities.
 
Manufactured from re-cycled polypropylene, it will withstand hot rolled asphalt. Designed with a heavy duty hinged lid that folds back on itself to avoid pedestrian accidents. The lid is retained in position with four robust, snap fit clip fittings, which do not require the use of a key. Giving a full 100mm x 125mm clear opening, and can be fitted with a galvanised detector plate if required.
 
Dimensions

185mm x 190mm x 75mm Depth
100mm x 125mm Clear opening

Test requirements as per ISO 306A BS2782/102A ASTM D 1525 - B7
Load Tested to Grade C as required in BS 5834 Part 2 1983

SID BOX SURFACE BOX

The Sid box surface box has a unique side-opening lid allowing for close abutment to adjacent walls. The lid is held in position with four robust retaining clips and a fully flexible hinge which allows the lid to completely folds back on itself, for easy access and reducing the risk of pedestrian injury.

The box has no external ribs for snug fit of paving slabs and the back of the box incorporates a slide out section (no drilling required) to enable easy cable entry, with an optional galvanised detector plate and lockable lid which can also be badged to your requirements.

Manufactured from recycled polypropylene it will withstand hot rolled asphalt.

Dimensions
130mm x 140mm x 75mm Depth
Test requirements as per ISO 306A BS2782/102A ASTM D 1525 - B7
Load Tested to Grade B as required in BS 5834 Part 2 1983

SWIVEL DEE-BOX

The surface Swivel Dee-Box is a convenient, low-cost solution for terminating of tele comms cabling. The flat surface on the back of the box enables a close fitting duct entry with positive duct stop (no more chipping out of cement for the installer).

The lid has a positive four point retaining snap in fit, the Dee-box will adapt from 54mm pipe entry to 25mm pipe entry, with the unique facility to swivel through 360º allowing easy duct entry from any position.

Manufactured from recycled polypropylene it will withstand hot rolled asphalt.

Dimensions
110mm x 80mm x 75mm Depth
Clear opening 5000 sq. mm
 
Test requirements as per ISO 306A BS2782/102A ASTM D 1525 - B7

CLEAT BOX
The triangular surface Cleat Box has a unique internal cleat fixing, for security of tele comms cabling, can be fitted with galvanised detector plate if required, and can be badged to your requirements.
 
Manufactured from recycled polypropylene it will withstand hot rolled asphalt.
 
Dimensions
130mm x 130mm x 75mm Depth
 
Test requirements as per ISO 306A BS2782/102A ASTM D 1525 - B7
Load Tested to Grade C as required in BS 5834 Part 2 1983